What is the hole size for M10 bolt?
Size | Clearance Hole | Tapping Drill (fine pitch) |
---|---|---|
M8 | 9 | 7 mm |
M10 | 11 | 9.0 or 8.75 mm |
M12 | 14 | 10.5 mm |
M16 | 18 | 16.5 mm |
How big should a bolt hole be?
Standard Holes Standard hole sizes for bolts are made 1/16-in. larger in diameter than the nominal size of the fastener body. This provides a certain amount of play in the holes, which compensates for small misalignment’s in hole location or assembly, and aids in the shop and field entry of fasteners.
What size drill bit is 10mm?
Metric Tap and Drill Bit Size Table
Tap | Metric Drill | US Drill |
---|---|---|
10mm x 1.5 | 8.7mm | – |
10mm x 1.25 | 8.9mm | 11/32″ |
10mm x 1.0 | 9.1mm | – |
12mm x 1.75 | 10.5mm | – |
What is the diameter of an M10 thread?
ISO Metric Thread Dimensions
Thread Size | Nominal Diameter (mm) | Effective Diameter (mm) |
---|---|---|
M10 | 10.0 | 9.026 |
M12 | 12.0 | 10.863 |
M14 | 14.0 | 12.701 |
M16 | 16.0 | 14.701 |
What is bolt hole spacing?
Hole Spacing You should review these sections. Probably the most commonly used bolts fall in the 3/4″ to 1″ diameter range. The commonly used spacings for these bolts are 3″ center-to-center of bolt and 1.1/2″ from center of hole to plate/member edges. These spacings satisfy the requirements of the specification.
What is bolt hole clearance?
A clearance hole is a hole through an object which is big enough to enable threads of a screw or bolt to pass through but not the head of the screw or bolt. It allows a screw to pass through it without the threads biting into the material.
What thread diameter is an M10?
Tap size | Basic major dia (mm) | Basic major dia (inch) |
---|---|---|
M8 x 1 | 8mm | .3150 |
M10 x 1.5 | 10mm | .3937 |
M10 x 1.25 | 10mm | .3937 |
M12 x 1.75 | 12mm | .4724 |
What size is an M10 nut?
10 mm
M10 nuts have a diameter of 10 mm and are one of the most common sizes of nut available.
How much tolerance does a bolt hole need?
ISO Tolerances For Bolt Fastener and Holes Table Chart ISO 286
Size | Tolerance Zone in mm (Internal Hole Features) | |
---|---|---|
over | to | H7 |
6 | 10 | +0.015 0 |
10 | 18 | +0.018 0 |
18 | 30 | +0.021 0 |
What size is a #10 hole?
0.1590″
They have slightly different requirements for some screw sizes.
Screw Size | Screw Threads per Inch | Recommended Hole Diameter |
---|---|---|
#10 | 12 | 0.1590″ |
#12 | 11 | 0.1875″ |
#14 / 1/4″ | 10 | 0.2188″ |
5/16″ | 9 | 0.2900″ |
What size hole do I drill for a 10mm tap?
Tap size | Basic major dia (mm) | Drill size (mm) |
---|---|---|
M8 x 1 | 8mm | 7mm |
M10 x 1.5 | 10mm | 8,5mm |
M10 x 1.25 | 10mm | 8,8mm |
M12 x 1.75 | 12mm | 10,2mm |
What size is a #19 drill bit?
Jobber Length Drill Bit: #19 Drill Bit Size, 2 1/8 in Flute Lg, 5/32 in Shank Dia. Country of Origin USA. Country of Origin is subject to change. Wire-size drill bits come in standard sizes that correspond to American Wire Gauge (AWG) sizes.
What does M10 mean?
M10 means a 10 millimeter outer diameter for the bolt or whatever piece it is; M12 means 12 millimeters. The part after the ‘x’ is the pitch — how many mm a thread is wide.
What size bolt has a 10mm head?
The standard 6mm cap screw has a 10mm head.
How far should a bolt hole be from an edge?
Minimum edge distance (distance between centre of the bolt hole to the plate edge) shall not be less than 1.25 times the nominal bolt diameter.
Are bolt holes always clearance holes?
Most bolt holes are made with “standard” clearance and are considered a normal fit. A normal fit provides relatively accurate positioning of assembled components while still allowing for slight misalignment.