What does seneye test for?

monitors the highly toxic free ammonia (NH3) at very low levels, so you can stop your fish from dying from Ammonia posioning. the seneye monitors pH in your aquarium or pond water between 6.4 and 9. This range is ideal for most aquatic life and by monitoring this range increased accuracy has be achieved.

Is the seneye any good?

The Seneye Reef is a great light meter. That you can get a full featured meter for PAR and color spectrum information for around $200 USD, about half what the comparable Apogee product costs is what makes this product amazing.

What is Seneye Reef monitor?

Seneye Reef Pack is an all in one monitor for Temperature, Ammonia, pH, Water level, and Lighting. With a PC you can connect your Seneye monitor directly to any PC or Seneye Web Server to monitor your aquarium.

How do I monitor my aquarium pH?

The most accurate method for testing aquarium water pH is to use an electronic pH meter. You may be able to purchase a pH meter from a local pet supply store. Or, if you have an iPhone, iPad, or Android, you can use our smart sensors to turn your smart device into an aquarium pH meter.

Does seneye work with Mac?

The SWS has a build in web page interface that can be used to view data locally and adjust the setting on the seneye device. This interface is fully Mac compatible, as to is the seneye.me dashboard.

How accurate is the seneye par meter?

The error was around 20% increasing a lot the closer you got to the illumination source. If you are not doing this for a living the seneye is close enough, if your reputation depends on it, I’d spend the bucks on something designed for the job.

How do you soak a Seneye slide?

Soak slide for 24 hours Remember to always soak your seneye slide for a minimum for 24 hours before using it. Take a glass of water from your aquarium or pond and place the slide in. Soaking allows the sensor pad time to stabilise so accurate readings can be taken.

What is the ideal pH for an aquarium?

6.8 to 7.8
Testing Aquarium pH pH – the measure of whether water is acidic (pH 1 to 7.0) or basic (pH 7.1 to 14). 7.0 is considered neutral. Most freshwater aquarium tropical fish do best at a pH of 6.8 to 7.8, although certain fish may require higher or lower levels.

Why is my aquarium pH so low?

Usually, the culprit behind low pH in an aquarium is poor maintenance. As fish waste and uneaten food collect in the aquarium, they break down and put off more and nitrate (NO3-). Nitrate is acidic. So, the more it builds up in the water, the more it drives the pH down.

How do I setup a Seneye Web server?

1. Power On. Plug the Micro USB power cable into the power port of the VIXMINI.
2. Connect.
3. Access the Web Admin Panel.
4. Go to the Internet section of admin panel.
5. Connect Vixmini to Seneye Web Server.
6. Finish setting up Vinimix.

How do you clean a Seneye?

Table of contents

1. Take the device out of the water and remove the back of the device.
2. Remove the seneye slide. Place your slide in the water that you are monitoring, if it dries up this can also effect readings.
3. Wipe the clear light window and sensor lenses with your finger and rinse off under water.

How do I update my Seneye?

Upgrade the light meter in your seneye Home or seneye Pond device to give you LUX, Kelvin and PAR. Once you have purchased the light meter update you must e-mail [email protected] and provide the serial number from the seneye device you would like upgraded.

How often does seneye take a reading?

The readings from your seneye device are uploaded to your personal seneye dashboard every 30minutes, when connected to a PC.

How do you set up a seneye Reef?

How to set up a device with a Windows PC/Tablet

1. 1.1. If you have not done so, please download the installer from the link below.
2. 1.2. Run the seneye connect installer.
3. 1.3. Log into the seneye connect software.
4. 1.4. Update the firmware on your seneye device.
5. 1.5. Activating Marine Tick.

Is 7.2 pH good for fish tank?

Live plants do best in a pH range between 6.5 and 7.5. Beneficial bacteria prefer a slightly higher range, from 7.0 to 8.0. In general, a good pH range that would satisfy most fish, along with live plants and bacteria would be 7.0 to 7.2.

How can I raise the pH in my aquarium fast?

How to raise pH in aquariums:

1. Use reverse osmosis (RO) or deionized (DI) water to create the desired pH and buffering.
2. Use crushed coral or dolomite gravel for substrate.
3. Decorate your aquarium with limestone or coral rock.
4. Fill a mesh media bag with crushed coral or dolomite gravel and place it in your filter.

How do I increase the pH in my aquarium?

6 Ways to Raise pH in a fish tank

1. Add Bicarbonates. Adding bicarbonates to the fish tank shows a significant rise in the pH content.
2. Add Rocks and Substrates.
3. Add Seashells.
4. Change the Water Regularly.
5. Increase Aeration in the Fish Tank.
6. Remove pH lowering objects.